DescriptionDia. (ft)Length (ft)Horsepower

9' x 10' Allis Chalmers Ball Mill - Refurbished

  • New Eaton 20" VC-1000 clutch
  • 400hp Seimens Synchronous Motor, 4160V, 60hz
  • New drives with spare parts
  • New starter
  • New rubber liners, installed
  • Brass trunnion inserts
  • Feed chute relined
  • Bull gear NDT. no cracks reported.
  • New bearings
  • Spare pinion, brass inserts, new clutch
  • 9
  • 10
  • 400
 DescriptionDia. (ft)Length (ft)Horsepower

9'x 6' Hardinge Tri-Cone Ball Mills (2)

  • Elliot 200HP & 350HP Motors
  • Falk 9GHC Reducers
  • Mill RPM: 18.2 & 23.8
  • Gearing: 10" Face, Herringbone
  • Last used in Zinc ore
  • 9
  • 6
  • 200
 DescriptionDia. (ft)Length (ft)Horsepower

Allis Chalmers 8' x 14' Ball Mill

  • Ring Gear Teeth: 318
  • Pinnion Teeth: 19
  • Mill Speed: 21.5 r.p.m.
  • Motor: 450 Hp, Frame 51C6, s/n 1-81-00-5033,Speed 360 r.p.m., 575v/3/60
  • Starter: Available – Benshaw new 1998
  • Clutch: Eaton
  • Mill is disassembled and was match marked
  • 8
  • 14
  • 450
 DescriptionDia. (ft)Length (ft)Horsepower

Denver 8’ x 12’ Ball Mill

  • Single helical bull gear 248 teeth
  • Pinion gear 19 teeth
  • 500HP GE Synchronous Electric Motor, 4000 volt, 1200 rpm
  • Falk gear box 4.483 - 1 ratio, input speed 1200rpm
  • 30” air clutch
  • Babbit main bearings, pinion shaft roller bearings
  • Manual hydraulic start up bearing lubricators
  • Sole plates & gear guards
  • No liners
  • 8
  • 12
  • 500
 DescriptionDia. (ft)Length (ft)Horsepower

8'x 12' Allis Chalmers Ball Mill (2)

  • 400 HP, 2300 volt, 180rpm
  • no liners
  • mills removed, ready for transport
  • 8
  • 12
  • 400
 DescriptionDia. (ft)Length (ft)Horsepower

8' x 10' Vecor Ball Mill - Refurbished

  • Skid mounted mill
  • 335kw (450HP), 6600v, 41.2 Amps, 50Hz, 989 rpm motor drive
  • 8
  • 10
  • 450
 DescriptionDia. (ft)Length (ft)Horsepower

Hardinge 8' x 10' Ball Mills (4)

  • Sister Units
  • General Electric 350 HP Motors
  • 1175 RPM
  • Falk Drive Through Pinion
  • Model: 111 / 2GHC
  • Ratio: 7.469
  • Rating: 350 - 540
  • Steel Lined (Liners Remain @ 50% New)
  • Units remain indoors and intact
  • 8
  • 10
  • 350
 DescriptionDia. (ft)Length (ft)Horsepower

Allis Chalmers 8' x 10' Ball Mill

  • herringbone gear
  • no liners
  • Motor: WEG, 400hp, 348 rpm, 600V/3/60
  • Direct drive
  • s/n: 870
  • Drawings available
  • removed, ready for transport
  • 8
  • 10
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

Allis Chalmers 8' x 8' Ball Mill

  • herringbone gear
  • no liners or motor
  • s/n: 802
  • removed, ready for transport
  • 8
  • 8
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

7' x 10' Denver Ball Mill.

 

  • GRATE DISCHARGE
  • WELDED STEEL SHELL
  • CAST STEEL FEED & DISCHARGE HEADS
  • DE-MOUNTABLE TRUNNIONS
  • MAIN BEARINGS WITH SOLE PLATES
  • RING & PINION DRIVE GEARS WITH GUARDS
  • METAL LINERS
  • BEARING LUBE SYSTEM
  • GEAR SPRAY
  • EXCLUDING 300 HP MOTOR & REDUCER
  • REPORTED TO BE IN GOOD OVERALL CONDITION
  • 7
  • 10
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

Allis Chalmers 7'x 9' Ball Mill

  • split bull gear
  • herringbone gear
  • babbitt bearing
  • s/n:580
  • removed, ready for transport
  • no motor
  • 7
  • 9
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

7' x 7' Allis Chalmers Ball Mill

  • 125HP 600V Electric Motor
  • Rubber liners
  • Drawings available
  • 24 rpm mill speed
  • Bull gear:303 teeth
  • Pinion: 15 teeth
  • 7
  • 7
  • 185
 DescriptionDia. (ft)Length (ft)Horsepower

6' x 16' Canadian Vickers Ball Mill

  • herringbone gear
  • 1/2" shell thickness
  • split bull gear
  • 13" bull gear width
  • 20" trunnion width
  • no pinion, motor or liners
  • 6
  • 16
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

6' x 16' Canadian Vickers Ball Mill

  • straight gear
  • 3/4" shell thickness
  • split bull gear
  • 13" bull gear width
  • 20" trunnion width
  • belt driven pinion
  • steel liners
  • 6
  • 16
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

Allis Chalmers 6' x 10' Ball Mill

  • herringbone gear
  • 250hp
  • Hamilton gear box H-1112 3.866:1 service factor 2.05 Rated for 250hp
  • removed, ready for shipment
  • 6
  • 10
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

6’ X 12’ Allis Chalmers Ball Mill

  • WELDED STEEL SHELL
  • CAST STEEL FEED & DISCHARGE HEADS
  • RING GEAR SINGLE HELICAL; 2 PIECE
  • PINION SHAFT ASSEMBLY WITH SOLE PLATES
  • MAIN BEARING ASSEMBLIES WITH SOLE PLATES
  • RUBBER LINERS
  • BEARING LUBRICATION SYSTEM
  • GEAR SPRAY SYSTEM
  • 200 HP, 1185 RPM MOTOR, 575 VOLT, 3PH, 60HZ
  • GEAR REDUCER
  • WITCHITA CLUTCH
  • SPARE PARTS
  • EXCLUDING: MOTOR CONTROLS
  • “AS IS” CONDITION, CLEANED, PRIMER COATED, AND PREPARED FOR TRANSPORT.
  • 6
  • 12
  • 200
 DescriptionDia. (ft)Length (ft)Horsepower

Dominion 6' x 10' Ball Mill

  • rubber lining
  • no motor, reducer or pinion
  • s/n 340-50
  • 6
  • 10
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

Hardinge 6' x 8' Ball Mill

  • No motor
  • Serial number R338
  • Trommel feed
  • Still in place, on foundations
  • 6
  • 8
  • 0
 DescriptionDia. (ft)Length (ft)Horsepower

Marcy 6’ x 6’ Ball Mill

  • spout feed, trunion overflow
  • c/w rubber liners (removed)
  • 100 HP, 3/60/1770 motor
  • mounted on structural steel frame
  • very good condition
  • 6
  • 6
  • 100
<< Start < Prev 1 2 Next > End >>
Page 2 of 2